How To Reset Check Engine Light After Replacing Mass Air Flow Sensor

Keeping the battery unhooked for longer than 10 minutes won't hurt anything. Then, vacuum out all dust/dirt/debris found inside both halves of the air filter housing.

Check Engine Light Problem Mass Airflow Sensor Houston Auto Repair Near You Santa Ana Auto Care – Houston Tx

Table of Contents

The passing air cools the wire down.

How to reset check engine light after replacing mass air flow sensor. Clean it with some spray intake and throttle body cleaner, then. This will indicate that your ecu has been reset. Check if the engine light is still on after the mass air flow sensor was replaced.

We sell oem air mass sensors, air flow meters, and hfms (hot film meter) for many bmws. When you change a maf sensor, you need to disconnect the battery for about 10 minutes so the computer forgets the learned parameters and resets to the factory parameters. This is because the computer in the car if it does not receive a reading from the mass airflow sensor, will estimate and supply a number that it thinks it is supposed to have.

If the “not ready” status becomes “ready” and the check engine light did not come back on, then the problem may have been an intermittent faulty sensor. If the check engine light does come back on then the scanner will show you that bad code again. The symptoms of a bad mass air flow sensor include low engine power, poor fuel economy, an engine that won’t start, a check engine light on the dash and a gas smell from the exhaust fumes.

Autozone and other places will plug in to your obdii port for free or you can buy a code scanner yourself. On and read code p0101 for mass air flow sensor. The job of the mass air flow sensor.

What did you think of this article? Make sure no other codes were present that may have came back. Its just to the right of center engine.

Wait five minutes and reinsert the fuse. If the check engine light was out after you did the repair and came back on later after starting the car or driving than another problem may have popped up. For the interior lights not working after replacing the battery, first check the switch to make sure that the light is on.

Car runs fine 1 answer i was only going about 2 miles an hour went thru a cracked piece of driveway in shopping center bit of a pot hole check engine light came on immediately after. Back on again and is reading the same code for the mass air flow sensor. Engine see's could make it set a code.

The entire system can be reset by unhooking the battery and leaving it unhooked for 10 minutes. I have a 2015 nissan sentra sr and a while back the check engine light came. Once you replace your mass airflow sensor, you will have to disconnect your car battery for some minutes (i recommend 10 to 15).

What to do after replacing mass airflow sensor. To remove this un screw the oil filler tube by hand and remove the top cover. This problem may or may not be caused by the mass airflow sensor.

I hit a bump yesterday and the check engine light came on. You only have to reprogram the computer if necessary. Maf is the sensor right after the air filter that is part of the intake.

I have changed my mass air flow sensor twice with oem parts, reset the code multiple times, put a new k&n air filter in and the light still comes with in 3 or so miles. The mass air flow sensor is located under the top plastic engine cover. Disconnect the battery for a couple minutes to reset the codes.

Could also be the maf is dirty. Then it goes into learn mode and may take a little while before it learns all the parameters of the new maf sensor. The reason you need to do this is for the car computer to reset to its factory setting and forget previously learned parameters.

If you disconnect the mass airflow sensor, then the car should keep running and still be able to start normally. You might consider the excellent gopoint cable and app for your iphone which can perform these functions better than many of the dedicated tools available. If it is the maf, and cleaning it was unsatisfactory, it will be need to be replaced.

Sensor and then cleared the code. First check to see what codes are being set which cause the check engine light to illuminate. How do i reset check engine light after replacing mass flow air sensor on 2006 pontiac solstice?

However, the check engine light just came. A bad mass air flow sensor is often the likely culprit if your car isn’t running as it should. If the light is on the door selection and will not turn on, then one of.

After you reset the codes, either of these two things will happen: I went and replaced the. The check engine light will blink, then shut off.

Remove the air filter element. Here is the tsb on replacing the mass air flow sensor. My car was diagnoised with a bad air flow sensor.

Well, the answer to that is no.

What To Do If Your Emission Light Comes On Leasecar Blog