The plates are located within the salt water chlorinator cell and are usually detachable. How to clean intex salt cell with vinegar compatible with:
Is dedicated to the safe use of all its products.
How to clean salt cell intex. First, turn off the filtration system. Place a dish or a small tub under the cell to catch any solution that may spill while pouring. Then, carefully remove the salt cell from the union connections.
Here's what you will need: Steps on how to repair a salt cell. Water will leak out, so try not to get soaked!
The copper ionization feature reduces chlorine levels by 70% when compared to. You can start cleaning the salt cell with a standard garden hose. If by some unlikely chance you find deposits on the charged plates, all you need to do is to follow the general salt cell cleaning guidelines to have your unit functioning optimally.
The water that you fill your pool with may contain high amounts of calcium. How to clean the intex saltwater chlorinator cell intex easy set saltwater system pool chlorinatorthe intex krystal clear saltwater system eliminates the need for dangerous, harsh chlorine while dramatically improving your pool's cleanliness and your comfort level. Next, slowly unscrew the unions to relieve pressure on the lines, and remove the cell for inspection and/or cleaning.
(chemically, table salt is nacl 2 —one sodium atom bonded to two chlorine atoms.) with a generator installed, you can dissolve enough salt in the pool water to bring the concentration to about 3,000 ppm. Point it in one end of the unit, letting the water go through it and flow out the other end. While all accidents cannot be avoided, practicing good safety habits, adjusting and following rules, carefully reading instruction manuals, and vigilance
Warning signs could be low free chlorine c. 0.78 lbs intex recreation corp. It has the same chemical composition as hydrochloric acid but contains extra compounds.
This process should help remove random bits that have gotten caught in there, as well as some of the mineral deposits. You will be inspecting the metal plates inside the salt cell. First, unplug the chlorine generator and turn off the circuit breaker for the pool pump.
With the system turned off, carefully remove the plates for easy and more thorough cleaning. Since the power is off, it is time to take the cell out of its housing to inspect it closely. The free plates should then be soaked in the cleaning mixture for 10 to 15 minutes depending on the concentration used.
How to clean the salt cell and remove scale buildup. To keep these pools clean and sanitized, intex sells its own line of pool supplies, and one of them is a saltwater chlorination system that works by extracting sanitizing chlorine from ordinary salt. While these systems can require less maintenance than other sanitizing systems, occasionally they may need attention.
It is advised to check the cell for deposits at least once every 4 or 5 months. 1) muriatic acid (sold in leslie's pool supplies stores) 2) plastic bucket or salt cell stand. If proper chlorine levels cannot be maintained, and if salt levels and ph readings are correct, the cell must be cleaned.
Then fill the unit with plain vinegar and let soak for few hours, then rinse with water. For more information, read our article on cleaning a cell with muriatic acid. Soak the plates in the prepared mixture.
Attach the cell to the stand, cord side down, and place it upright. Cleaning salt cell with muriatic acid is one of the best ways to clean the minerals built up on the cell plates. When cleaning the salt cell, you can give it an acid bath that consists of 90% water to 10% acid.
It is very easy to inspect the salt cell to determine if it needs a thorough cleaning. Remove the cell portion and cap one end with cap that the unit came with. But remember to bathe the cell for 10 minutes because the acid can eat away those plates.
The time period to clean the chlorease cell will vary. You add salt directly to the pool water—the intex system does not have a salt reservoir. Then brush the calcium deposits using a toothbrush.
Your saltwater chlorinator cell should come with a cleaning stand (basically a stand that allows the cell to stand vertically). Below are a few simple steps to follow when using muriatic acid to clean your salt cell… Once the salt chlorinator cell.
Also, it is very easy to remove the cell and all you need to do is to unscrew. Now, rinse the cell plates with a garden hose. The chlorinator cell housing is clear allowing you to quickly assess the condition of the cell.
These make it great as a sanitization compound as it targets both the minerals and other organic and living matter in the cell.